Win XP Bluescreen

Origano

Lt. Commander
Registriert
Jan. 2004
Beiträge
1.571
... in letzter Zeit immer häufiger verabschiedet sich meinWin (XP mit SP 2 und allen Updates) urplötzlich mit dieser Meldung.
Und zwar sehr häuffig, wenn ich mit dem IE 6 beim surfen bin.
Temperaturen ect. sind alle im grünen Bereich, daran kann es nicht liegen, das Netzteil ist ein Levicom 500 Watt.
Asus A7N8X-E deLuxe, AMD Athlon 3200+, Ati Radeon 9800Pro, 2 WD HDD's im Raid0 Verbund, 3 x Corsair 512 MB im Dual channel...

Hat jemand einen Plan ?
 

Anhänge

  • IMG_0113.JPG
    IMG_0113.JPG
    132,6 KB · Aufrufe: 239
AW: Und tschüss...

Updates sind oft die Folge von abstürzen.

geh ma auf die seite Microsoft homepage und gib in der suchleiste oben rechts 282784.
Du erhält glaub ich einen link, über den du dann >> Qfecheck.exe<< downloaden kannst. Mach das und installier das tool...
nach der Instalation starte die Kommandozelle und gib den befehl
qfecheck /v
Jetzt werden alle installierten Hotfiyes auf fehler überprüft. Entdeckt das tool ein defektes Update, erhälst du einen Hinweis, dass der Hotfix XY fehler ausweist und man s deinstallieren und neu installieren muss. Mach das, und dann müsste hoffentlich alles gelöst sein

Viel erfolg
MfG
 
Zuletzt bearbeitet:
AW: Und tschüss...

Es kann auch sein, daß sich einer deiner 3 Corsair Speicherriegel irgendwie verarscht fühlt, und nicht mehr mag. Teste das mal mit Memtest86+.
 
AW: Und tschüss...

@ Origano: soory. da kann ich auch nix machen... bei mir wills auch nicht runterladen...
 
AW: Und tschüss...

General Troubleshooting of STOP Messages
If you can’t find a specific reference to your problem, running through the following checklist stands a good chance of resolving the problem for you.
This checklist is also usually the best approach to troubleshooting some specific Stop messages, such as 0x0A and 0x50.

1. Examine the “System” and “Application” logs in Event Viewer for other recent errors that might give further clues.
To do this, launch EventVwr.msc from a Run box; or open “Administrative Tools” in the Control Panel then launch Event Viewer.
2. If you’ve recently added new hardware, remove it and retest.
3. Run hardware diagnostics supplied by the manufacturer.
4. Make sure device drivers and system BIOS are up-to-date.
5. However, if you’ve installed new drivers just before the problem appeared, try rolling them back to the older ones.
6. Open the box and make sure all hardware is correctly installed, well seated, and solidly connected.
7. Confirm that all of your hardware is on the Hardware Compatibility List.
If some of it isn’t, then pay particular attention to the non-HCL hardware in your troubleshooting.
8. Check for viruses.
9. Investigate recently added software.
10. Examine (and try disabling) BIOS memory options such as caching or shadowing.
Mehr hier: http://support.microsoft.com/?kbid=314063&sd=RMVP
 
AW: Und tschüss...

@ Rafl B.
Wo haste die Exe datei her?
thx... ;)
 
AW: Und tschüss...

drei Riegel und dual channel das geht eigentlich garnicht nimm einen riegel raus
 
AW: Und tschüss...

Oh Sorry, war die spanische. oben gibts ein update ;)
 
AW: Und tschüss...

welche Spanische?
geht immer noch nicht! jetzt kann ich das zwar laden, jedoch bekomme ich beim öffnen immer wieder eine Fehlermeldung :( :confused_alt:
 
AW: Und tschüss...

Socrates schrieb:
drei Riegel und dual channel das geht eigentlich garnicht nimm einen riegel raus
Wenn man keine Ahnung hat, einfach mal die Finger still halten. :rolleyes:

Der nforce2 Chipsatz kann sehr wohl mit drei Speicherriegeln Dual Channel.
 
AW: Und tschüss...

Gonzo71 schrieb:
Wenn man keine Ahnung hat, einfach mal die Finger still halten. :rolleyes:

Der nforce2 Chipsatz kann sehr wohl mit drei Speicherriegeln Dual Channel.


Hatte das falsche board im kopf
 
Zurück
Oben