BIOS piepst bei FSC i845G Komplettsystem

gTm

Cadet 3rd Year
Registriert
Apr. 2009
Beiträge
54
Hallo,

habe hier einen FSC PC mit Service ID YBSX447572.
Leider fährt der PC nicht mehr hoch.
Beim Booten läuft er an - schaltet dann kurz aus und wieder an - und dann kommt folgende Piepserei: piep - pause - piep pieb pieb - pause - pieb pieb pieb - pause - pieb
Leider kann ich nicht heruasfinden welches Mainboard verbaut ist. Wahrscheinlich ein FSC OEM Board? Somit weiss ich auch nicht was das für ein Fehlerhinweis sein könnte.
Hat jemand eine Idee dazu? Habe ehrlich gesagt auch keine Ahnung wie ich weiter vorgehen soll, da ansonsten alles dunkel bleibt.

Grüße

gTm
 
Wenn das ein Komplett system ist hast du bestimmt auch ein Handbuch und das sollte dir dann weiter helfen können und wenn du das nicht mehr hast guck mal ob du das noch downloaden kannst.
 
Am einfachsten ist es, wenn du bei FSC anrufst und die Service-ID und deinen Beep-Code durchgibst. Die können dann sehen, was für ein Fehler das ist. Leider sind nicht alle Beep-Codes im Kundenhandbuch und im Bios-Kompendium gelistet.
Tel-Nr. von FSC: 01803777011
 
Sorry, dein PC ist mir zu alt, bekomm ich kaum Informationen dafür...
Wie wär's mal mit nem neuen?
(Zur Info: ich arbeite bei einem Fujitsu-Service-Partner)
 
FSC hat das Phoenix BIOS: Hier die BEEP codes:

Phoenix BIOS Beep Codes

Phoenix BIOS verwendet Kombinationen aus langen und kurzen Tönen. In der Tabelle steht das '-' für eine kurze Pause zwischen den Tönen. Beispielsweise steht 1 - 1 - 2 für lang, lang, kurz, kurz.
BEEP CODE Bedeutung Mögliche Ursache
1 - 1 - 2 CPU / motherboard failure Bad CPU / motherboard
1 - 1 - 3 CMOS read/write failure Bad motherboard
1 - 1 - 4 BIOS ROM failure Bad BIOS chip
1 - 2 - 1 Timer failure Bad motherboard
1 - 2 - 2 DMA failure Bad motherboard
1 - 2 - 3 DMA failure Bad motherboard
1 - 3 - 1 Memory refresh failure Bad memory
1 - 3 - 2 64K memory failure Bad memory
1 - 3 - 3 64K memory failure Bad memory
1 - 3 - 4 64K memory failure Bad memory
1 - 4 - 1 Address line failure Bad memory
1 - 4 - 2 Parity error Bad memory
1 - 4 - 3 Timer failure Bad motherboard
1 - 4 - 4 NMI port failure Bad motherboard
2 - 1 - 1 64K memory failure Bad memory
2 - 1 - 2 64K memory failure Bad memory
2 - 1 - 3 64K memory failure Bad memory
2 - 1 - 4 64K memory failure Bad memory
2 - 2 - 1 64K memory failure Bad memory
2 - 2 - 2 64K memory failure Bad memory
2 - 2 - 3 64K memory failure Bad memory
2 - 2 - 4 64K memory failure Bad memory
2 - 3 - 1 64K memory failure Bad memory
2 - 3 - 2 64K memory failure Bad memory
2 - 3 - 3 64K memory failure Bad memory
2 - 3 - 4 64K memory failure Bad memory
2 - 4 - 1 64K memory failure Bad memory
2 - 4 - 2 64K memory failure Bad memory
2 - 4 - 4 64K memory failure Bad memory
2 - 4 - 4 64K memory failure Bad memory
3 - 1 - 1 Slave DMA failure Bad motherboard
3 - 1 - 2 Master DMA failure Bad motherboard
3 - 1 - 3 Interrupt controller failure Bad motherboard
3 - 1 -4 Slave IC failure Bad motherboard
3 - 2 -2 Interrupt Controller failure Bad motherboard
3 - 2 - 3 <RESERVED>
3 - 2 - 4 Keyboard control failure Bad motherboard
3 - 3 - 1 CMOS batter failure Bad CMOS battery
3 - 3 - 2 CMOS configuration error Incorrect setting
3 - 3 - 3 <RESERVED>
3 - 3 - 4 Video memory failure Bad video card or memory
3 - 4 - 1 Video init failure Bad video card or memory
4 - 2 - 1 Timer failure Bad motherboard
4 - 2 - 2 CMOS shutdown failure Bad motherboard
4 - 2 - 3 Gate A20 failure Bad motherboard
4 - 2 - 4 Unexpected interrupt Bad processor
4 - 3 - 1 RAM test failure Bad memory
4 - 3 - 3 Timer failure Bad motherboard
4 - 3 - 4 RTC failure Bad motherboard
4 - 4 - 1 Serial port failure Bad motherboard
4 - 4 - 2 Parallel port failure Bad motherboard
4 - 4 - 3 Coprocessor failure Bad motherboard or CPU.
9 - 2 - 1 Video adapter incompatibility Use a different brand of video card

1 3 4 bedeudet bei Dir: Speicherfehler

Hier dei Info zum Mainboard: Es ist ein D1386 bzw D 1387
Der Link zum Handbuch: http://support.ts.fujitsu.com/Manuals/ShowDescription_KMT.asp?DokuID=202825
 
Zuletzt bearbeitet: (Info zum Mainboard hinzugefügt)
Hallo,

also ist sowieso nicht mein PC ich sollte nur mal einen Blick drauf werfen.
Danke für die Beepcodes.
Ansonsten habe ich das Handbuch schon davor gefunden aber das ist eher mager als das es einen weiterbringt...
PC wird wohl sterben...da noch groß etwas dran zu machen ist wohl wenig sinnvoll...

Grüße

gTm
 
Verstehe ich jetzt nicht ganz. Sind doch insgesamt 8 Pieps dann passt das mit dem 1 - 4 - 1 Fehler doch nicht?!
 
Zurück
Oben