Pc läuft nur mit 4GB Ram

Carlos94

Cadet 2nd Year
Registriert
Juni 2019
Beiträge
17
Hallo, habe von einem Kumpel folgende Komponenten bekommen:

CPU:AMD Phe II X6 1090T 3200 AM3
Mainboard: GiGabyte Mainboard GA-990FXA-UD7
Grafikkarte: Nvidia GTX 560 von Zotac
CPU Kühler: Beqiet Dark Rock pro 3
Arbeitsspeicher 8GB DDR 3 1600 Von Crucial

Habe mir dann eine neue SSD gekauft und wollte Windows neu installieren. Problem aber ist, dass ich mit dem 8GB Riegel nur eine Fehlermeldung "C1" auf dem Board bekomme, und ich kein Windows installieren kann (auf allen Slots). Nur wenn ich einen alten 4Gb Ram einsetze, startet er und ich kann Windows installieren.
Ist Windows dann installiert, kann ich den 8Gb Riegel einsetzen und er startet nun auch damit, allerdings kommen ständig und unvorhergesehen (aber auch oft bei Neuinstallationen) Bluescreens (auch auf allen Slots getestet). Lediglich, wie beim Installieren, mit einem alten 4Gb Ram läuft alles einwandfrei.
Setzt man dann aber 2x 4Gb ein (auf den Slotkombinationen 1-3 und 2-4 getestet, dann habe ich bei der Neuinstallation und im Betrieb das gleiche Problem.
Kann das vielleicht am Bios liegen? Batterie war nämlich leer, sprich Bios hat sich nach dem Ausbau resetet. Davor lief der Pc ja einwandfrei bei meinem Kollegen.

Vielen Dank schonmal im voraus!

Gruß
 
Die neuinstallation war sinnfrei.

Kann ja mal schauen wie der Ram im Bios erkannt wird oder ob du vieleicht eine ander Spannung für den Ram brauchst.
 
Zuletzt bearbeitet:
  • Gefällt mir
Reaktionen: Carlos94
Steckt der 2. Riegel auch im richtigen Slot?
792177
 
Carlos94 schrieb:
Kann das vielleicht am Bios liegen? Batterie war nämlich leer, sprich Bios hat sich nach dem Ausbau resetet. Davor lief der Pc ja einwandfrei bei meinem Kollegen.
Naja, am BIOS liegts eventuell, zB kann es sein, dass da davor andere RAM-Settings drin waren. Vielleicht war der RAM davor schon instabil und wurde statt mit 1600 mit 1333 oder noch weniger betrieben. Dann kanns natürlich sein, dass jetzt, wo er "richtig" eingestellt ist, wieder nicht stabil läuft. Bei so alten Kisten weiß doch niemand mehr, wann wer was eingestellt hat und warum.

Deine Problem sind eindeutig: mindestens ein RAM-Riegel läuft mit diesen Settings fehlerhaft. Entweder austauschen oder versuchen ihn runterzutakten.

Absolute Pflicht: Die neuen Settings müssen mit Memtest86 (mit oder ohne Plus, egal) getestet werden und dabei darf es keinen einzigen Fehler geben.
 
doch kann am BIOS liegen wenn der RAM z.b. mehr Spannung braucht um gut zu laufen ..

Aber leider keine wirklich passenden Infos über den Speicher genau... CPU-Z kann da helfen.
 
  • Gefällt mir
Reaktionen: Carlos94
stoeggich schrieb:
Das liegt ehr nicht am Bios. (Lade mal die Standarteinstellungen)
Die hat er schon durch die leere Batterie. Und doch: es kann sehr wohl daran liegen, aber eben nicht direkt am BIOS sondern eben GENAU daran, dass jetzt wieder die Standardeinstellungen drin sind, sprich: RAM wird richtig angesteuert
 
rg88 schrieb:
Absolute Pflicht: Die neuen Settings müssen mit Memtest86 (mit oder ohne Plus, egal) getestet werden und dabei darf es keinen einzigen Fehler geben.
Ich würde sogar sofort einen Memtest laufen lassen, und zwar mit jedem Riegel einzeln!
 
Lief dieser RAM denn schonmal auf dem Board?
Ist das BIOS aktuell?
 
Er schrieb doch, dass der Ram bei seinem Kumpel bereits lief, allerdings weiß ich nicht, ob dieser es ihm nur so sagte, oder er es selber sah!?
 
Ram lief definitiv auf dem Board vorher.
Leider habe ich nun auch mit 4Gb Ram Bluescreens bekommen -.-
Habe die Fehler mal mit WhoCrashed auslesen lassen:

On Sun 16.06.2019 19:13:34 your computer crashed or a problem was reported
crash dump file: C:\Windows\Minidump\061619-6500-01.dmp
This was probably caused by the following module: hal.dll (hal+0x47803)
Bugcheck code: 0x124 (0x0, 0xFFFFB38AADA7F028, 0xB64EC000, 0x135)
Error: WHEA_UNCORRECTABLE_ERROR
file path: C:\Windows\system32\hal.dll
product: Microsoft® Windows® Operating System
company: Microsoft Corporation
description: Hardware Abstraction Layer DLL
Bug check description: This bug check indicates that a fatal hardware error has occurred. This bug check uses the error data that is provided by the Windows Hardware Error Architecture (WHEA).
This is likely to be caused by a hardware problem.
The crash took place in the Windows kernel. Possibly this problem is caused by another driver that cannot be identified at this time.



On Sun 16.06.2019 19:13:34 your computer crashed or a problem was reported
crash dump file: C:\Windows\MEMORY.DMP
This was probably caused by the following module: pshed.dll (PSHED!PshedBugCheckSystem+0xB)
Bugcheck code: 0x124 (0x0, 0xFFFFB38AADA7F028, 0xB64EC000, 0x135)
Error: WHEA_UNCORRECTABLE_ERROR
file path: C:\Windows\system32\pshed.dll
product: Betriebssystem Microsoft® Windows®
company: Microsoft Corporation
description: Plattformspezifischer Hardwarefehlertreiber
Bug check description: This bug check indicates that a fatal hardware error has occurred. This bug check uses the error data that is provided by the Windows Hardware Error Architecture (WHEA).
This is likely to be caused by a hardware problem.
The crash took place in a Microsoft module. Your system configuration may be incorrect. Possibly this problem is caused by another driver on your system that cannot be identified at this time.



On Sun 16.06.2019 19:05:56 your computer crashed or a problem was reported
crash dump file: C:\Windows\Minidump\061619-6250-01.dmp
This was probably caused by the following module: ntoskrnl.exe (nt+0x1BC810)
Bugcheck code: 0xE3 (0xFFFFD48F81A96E50, 0xFFFFD48F88A8E040, 0xFFFFD48F852D4B90, 0x2)
Error: RESOURCE_NOT_OWNED
file path: C:\Windows\system32\ntoskrnl.exe
product: Microsoft® Windows® Operating System
company: Microsoft Corporation
description: NT Kernel & System
Bug check description: This indicates that a thread tried to release a resource it did not own.
This appears to be a typical software driver bug and is not likely to be caused by a hardware problem.
The crash took place in the Windows kernel. Possibly this problem is caused by another driver that cannot be identified at this time.



On Sun 16.06.2019 18:29:07 your computer crashed or a problem was reported
crash dump file: C:\Windows\Minidump\061619-6515-01.dmp
This was probably caused by the following module: ntoskrnl.exe (nt+0x1BC810)
Bugcheck code: 0x101 (0x20, 0x0, 0xFFFFA9013EE80180, 0x2)
Error: CLOCK_WATCHDOG_TIMEOUT
file path: C:\Windows\system32\ntoskrnl.exe
product: Microsoft® Windows® Operating System
company: Microsoft Corporation
description: NT Kernel & System
Bug check description: This indicates that an expected clock interrupt on a secondary processor, in a multi-processor system, was not received within the allocated interval. This can be caused by non-responding hardware or by a overheated CPU (thermal issue).
The crash took place in the Windows kernel. Possibly this problem is caused by another driver that cannot be identified at this time.



On Sun 16.06.2019 18:00:19 your computer crashed or a problem was reported
crash dump file: C:\Windows\Minidump\061619-8156-01.dmp
This was probably caused by the following module: hal.dll (hal+0x47803)
Bugcheck code: 0x124 (0x0, 0xFFFFB88243A7F028, 0xB64BC000, 0x135)
Error: WHEA_UNCORRECTABLE_ERROR
file path: C:\Windows\system32\hal.dll
product: Microsoft® Windows® Operating System
company: Microsoft Corporation
description: Hardware Abstraction Layer DLL
Bug check description: This bug check indicates that a fatal hardware error has occurred. This bug check uses the error data that is provided by the Windows Hardware Error Architecture (WHEA).
This is likely to be caused by a hardware problem.
The crash took place in the Windows kernel. Possibly this problem is caused by another driver that cannot be identified at this time.



On Sun 16.06.2019 17:29:33 your computer crashed or a problem was reported
crash dump file: C:\Windows\Minidump\061619-6875-01.dmp
This was probably caused by the following module: hardware.sys (hardware)
Bugcheck code: 0x3B (0xC0000005, 0xFFFFF8062902F0D9, 0xFFFFCB084E7BEE70, 0x0)
Error: SYSTEM_SERVICE_EXCEPTION
Bug check description: This indicates that an exception happened while executing a routine that transitions from non-privileged code to privileged code.
This appears to be a typical software driver bug and is not likely to be caused by a hardware problem.
A third party driver was identified as the probable root cause of this system error. It is suggested you look for an update for the following driver: hardware.sys .
Google query: hardware.sys SYSTEM_SERVICE_EXCEPTION
 
Netzkabel ziehen, dreimal auf den Startknopf drückem und PC öffnen.
Die beiden Pin für CMOS-Reset mit einen Schlitzschraubendreher brücken und PC neu starten.

RAM mit Memtest mindestens drei Durchläufe testen:
Memtest 86+
 
Ich habe GENAU das gleiche Problem auf einem Asrock 890GX Extreme 3 mit einem FX 6100. Bin gespannt was hier rauskommt.
 
Habe jetzt im Bios die Spannung für den Ram angepasst und seitdem kein Bluescreen mehr.
Danke für die Hilfe!
 
  • Gefällt mir
Reaktionen: DannyA4
Nice! Danke fürs Berichten!
 
Hallo Valin1984,
hat es dir auch geholfen? Also ich habe bis jetzt immer noch nichts, selbst (vorher nie getraut) unter Vollbelastung.
 
Zurück
Oben